Johns Creek, GA – Plumber

Inspected a standard Rheem Professional Classic Plus gas water heater (Model PRO+G75-76N RH) and found no visible leaks, corrosion, or other anomalies at the tank, drain pan, gas connection, or vent. Verified the factory-specified replacement magnesium anode rod (Rheem Protech SP11524C, 3/4" NPT) for this model to support tank service and corrosion protection.

Responded to plumbing repair call for multiple issues including leaking shower head on Pfister Iyla fixtures suspected to be caused by faulty diverter valve, running toilet, and water hammer in upstairs sink. Performed system pressure test reading approximately 80 psi to diagnose plumbing system conditions and identify potential causes of knocking pipes. Addressed leak repair and evaluated fixture components to restore proper operation.

Responded to report of two non-functioning sinks in bathroom. Upon inspection, determined the issue was related to the shower fixture system rather than separate sink fixtures. Evaluated the chrome shower control valves and tub spout assembly mounted on the tiled wall. Assessed water flow and pressure through both the overhead rainfall showerhead and handheld shower unit on the slide bar. Tested all control mechanisms to verify proper operation and restored full functionality to the shower system.

Replaced failed evaporator coil on Goodman furnace system in attic installation. Removed corroded coil assembly showing extensive rust damage at connection points and base, installed new coil unit, and reconnected refrigerant lines and ductwork to restore proper system operation.

Completed comprehensive HVAC maintenance on Goodman furnace system located in attic space. Performed full system inspection including furnace unit, air handler, ductwork, electrical connections, and condensate drain lines. All components found operating within normal parameters, filters checked, and system confirmed ready for continued service.

Responded to service call for clogged condensate line in basement mechanical area. Upon inspection, located condensate drain system near air handler with visible blockage preventing proper drainage. Cleared obstruction from PVC condensate line using appropriate tools and techniques. Verified water flow through drain line and confirmed system was draining freely. Tested air handler operation to ensure condensate removal system functioning properly. System restored to normal operation with no further drainage issues observed.

Completed copper pipe repair beneath cabinet fixture. Addressed severely corroded copper piping that exhibited extensive green patina, verdigris, and heavy oxidation from prolonged moisture exposure. Removed deteriorated white insulation material that had become heavily water-damaged, discolored, and compromised around the pipe connections. Replaced corroded copper fittings and sections showing advanced corrosion with pitted surfaces and multiple oxidation patterns. Installed new copper components and properly insulated repaired sections to prevent future moisture intrusion and corrosion.

Performed inspection of domestic hot water system with significant corrosion and pipe failure at connection point between PVC and metal piping. Documented severe deterioration, visible hole in insulated section, and evidence of active leaking with rust and mineral deposits. Recommend immediate replacement of damaged section to prevent further water damage and potential system failure.

Responded to customer report of kitchen sink leak. Upon inspection, checked water pressure with gauge to identify source of leak. Located and repaired compromised fitting under sink that was causing water seepage. All connections tested and confirmed watertight after repair.

Responded to service call for Rheem Classic Plus Professional 73-gallon gas water heater producing constant humming noise. Inspected unit and associated plumbing components including expansion tank, pressure relief valve, and ventilation system. Resolved humming issue and verified proper operation of all water heater components.

Responded to service call for tankless water heater with no hot water output and no error codes displaying. Inspected gas meter and supply line connections to verify adequate gas flow to unit. Determined issue was related to gas supply restriction. Cleared obstruction in gas line and restored proper operation of tankless water heater. System now producing hot water as designed.

Customer called for kitchen sink clog. Arrived at property to diagnose. Kitchen sink drain is disconnected and backup can be seen in 2” piping. Inspected piping below kitchen area. Checked pressure to property and static pressure is 60 psi. Used flex shaft to clear kitchen line blockage. Flex shaft has been ran throughly through kitchen line. Used supply line to test drainage before rework of kitchen sink drain. Connected new piping for kitchen sink drain. Performed fill test and system is working properly. Replaced faucet supply line for customer underneath kitchen sink and underneath bar sink. Restored water to fixtures amd system is working properly.

Customer called for water heater making rattling noise every so often. Arrived at property to diagnose. Ran fixtures for a Ran fixtures for an extended period of time and noise was able to be re-created. Noise is coming from current recirculation pump. Please refer to attached estimates to replace recirculation pump. Current temperature of water heater is set to 130°F. Heater does not have a thermal expansion tank installed. Installed new 2.1 gallon thermal expansion tank. Expansion tank has been pressurized to 45 psi. Restored water to heater and system is working properly. Static psi to property is 40. Preformed pressure drop test of lavatory faucet and pressure dropped to 35psi. Current pressure regulator valve is working properly. Water heater is from 2019.